Skip to content

How to install EPSON L220 printer

How to install EPSON L220 printer

How to setup EPSON L220 printer

Follow these instructions to install the Epson L220 printer correctly. Download and configure the driver for free and fill out the ink tanks with Epson Econ Tank technology. If you just need the EPSON L355 Driver, go to step 6 now. Let’s begin:

Step 1:

🥇 Epson L220

If this is a new printer, you have to be sure that you are removing all tape and package materials and double check that you are not missing anything in the box:

Epson L355 in the box
Epson L355 in the box.

Note: Do not open the ink bottles until you are ready to fill the ink tanks. The ink bottles are vacuum packed to maintain reliability.

  • A) The printer’s power cable is packed inside the printer. Be sure to remove it.
Epson L355 unbox
Epson L355 unbox.
  • B) Do not pull the ink tubes.
Epson L355 dont full the ink tubes
Epson L355 dont full the ink tubes.
  • C) Remove the transportation caps from each ink tank and store them on the inside of the ink tank unit. Only use the transportation caps when transporting the printer.
Epson L355 remove the transformation caps
Epson L355 remove the transformation caps.

Do not turn on the printer yet

Step 2:

🎯 Epson L220 Fill ink tanks

This printer uses 4 Epson Eco Tank ink bottles T664: one black; one blue; one yellow & one magenta bottle. Make sure you have the correct bottles in case you are buying replacements.

Keep the ink bottles out of the reach of children and do not drink the ink. If ink gets on your clothes or belongings, it may not come off

  • A) Open the ink tank unit cover, then remove the ink tank cap.
open the Ink tank cap
Open the Ink tank cap.

Note: Refer to the color-coded sticker on the ink tank unit to identify the color of each tank.

  • B) Unpack the black (BK) ink bottle. Hold the ink bottle upright and slowly turn the bottle cap to remove it.
close bottle
Close bottle.

Do not shake or squeeze the ink bottles. Do not touch the top of the ink bottle after its cap is removed

  • C) Match the ink color with the correct tank and then fill each tank with ink up to the upper line on the tank:
Match the ink color
Epson L355 Match the ink color.

Note: Do not force the bottles into position; they are keyed for each color.

  • D) Wait for the ink to fill the tank. Do not squeeze the bottle.
 dont squeeze the bottle
Dont squeeze the bottle.

Note: Ink flows into the tank and stops automatically when the ink tank is filled to the upper line. If ink does not flow from the bottle, lift and reinsert the bottle.

 ink colors
Epson L355 ink colors.
  • E) Replace the ink tank cap securely.
replace ink cap-securely
Replace ink cap-securely.

Do not leave the ink bottle inserted; otherwise the bottle may be damaged or ink may leak. If any ink remains in the bottle, store the bottle upright for later use

  • F) Seal each bottle with its tip.
Seal each bottle with its tip
Seal each bottle with its tip.
  • G) Repeat the previous steps for the other colors.
Repeat the previous steps for the other colors
Repeat the previous steps for the other colors.
  • H) Close the ink tank unit.

Step 3:

Turn on and charge the ink

This printer requires careful handling of ink. If ink spills, wipe it off immediately with a damp towel to avoid permanent stains. If ink gets on your clothes or belongings, it may not come off. Epson cannot guarantee the quality or reliability of non-genuine ink, may cause damage that is not covered by Epson’s warranty.

  • A) Connect the power cord to the back of the printer and to an electrical outlet.
Connect the power cord
Connect the power cord.

Do not connect to your computer yet

  • B) Press the stop button for 3 seconds until the power light starts flashing.
press power button for 3 seconds
Epson L220 press power button for 3 seconds.

Ink charging takes about 20 minutes. When the power light stops blinking, ink charging is complete

Ink charging takes approximately 20 minutes
Ink charging takes approximately 20 minutes.

Warning: Do not turn off the printer, open the front cover, or load paper while the printer is charging or you’ll waste ink.

dont disconnect or turn off the printer
Don’t disconnect or turn off the printer.

Note: Use the ink bottles included with the printer to set up the printer. Part of the ink will be used to charge the print head. These bottles may print fewer pages compared with subsequent ink bottles.

Step 4:

Load paper

  • A) Make sure the printer is not charging ink. Then flip the feeder guard forward, raise the paper support, and tilt it backwards slightly.
raise the paper support
Raise the paper support.
  • B) Load A4- or letter-size paper, glossy or printable side up and short edge first, in the middle of the rear paper feed slot.
load paper
Load paper.
  • C) Don’t load the paper sideways; always load it short edge first.
Dont load the paper sideways
Dont load the paper sideways.
  • D) Slide the edge guides against the paper, but not too tightly, then flip the rear feeder guard back.
Slide the edge guides against the paper
Slide the edge guides against the paper.

Step 5:

Epson L220 Driver

To be able to install the Epson L220 driver, you must have the ink and paper in the printer already settled up; otherwise, you will not be able to complete the installation. You cannot plug in the USB cable yet, wait until the installation software asks you do it.

  • A) Find the installation software included in the printer box.
  • B) Insert the installation disk in the CD/DVD unit of your computer. Open the windows explorer (“My PC” or “My computer”) and run the installation software.

If you don’t have or have lost the installation CD, you can download it here for free:

✅ Download Epson L220 Driver

Epson L220 Driver Windows 7, Windows 10
(32-bit & 64-bit) & macOS

Insert the software disk in your computer
Insert the software disk in your computer

Download Driver EPSON L220 Windows

Download Driver EPSON L220 Apple MAC

NOTE: This package includes the installation software and Drivers, installer and optional software.

Congratulations, you have installed you EPSON L220 printer successfully!!

Start

How to connect Epson L220 printer to WiFi?

The EPSON L220 printer does not have WiFi connectivity. You must use it connecting the USB cable included with your printer. In case you have a printer with WiFi connectivity, check these articles to know How to connect your Epson Printer to WiFi & How to print from mobile devices:

Epson Econ Tank Ink Bottle T544

Summary
🥇 How to install EPSON L220
Article Name
🥇 How to install EPSON L220
Description
✅ Epson L220 Driver A) Find the installation software included in the printer box. B) Insert the installation disk in the CD/DVD unit in your computer. Open the windows explorer (“My PC” or “My computer”) and run the installation software.
Author
Publisher Name
InstallingPrinter.com
Publisher Logo
Advertisment ad adsense adlogger